TWISP CLEARO POD FAQs
WHAT IS THE DIFFERENCE BETWEEN THE TWISP CLEARO 3 AND TWISP CLEARO POD?expand_more
The Clearo Pod is a refillable Pod style device in a more compact form-factor. The Clearo Pod offers adjustable airflow and adjustable power which can be boosted. Compared to the Clearo 3 it features a larger battery and a replaceable, refillable pod for easy flavour changes.
HOW DO I ADJUST THE AIRFLOW ON MY TWISP CLEARO POD?expand_more
The Twisp Clearo Pod has an adjustable airflow control ring at the atomiser base of the pod. The benefit of this is to better customise the airflow and tailor it to your preferred vaping style or flavour. It also offers a wider range of airflow for those that prefer a looser draw, or to balance out the extra power on hand. Adjust the airflow ring on the atomiser base found at the bottom of the pod and test it by both drawing air through before inserting, and then after inserting and activating - until you are satisfied with the perfect Classic (MTL) experience to suit your vaping needs. Once inserted, the pod airflow will remain perfectly tuned until you want to change it up again.
Twisp Clearo Pod airflow advantages:
- Wide adjustment possible
- Easy adjustment
- Set airflow per pod, and per flavour profile for a unique flavour experience
- Smooth airflow
HOW DO I REPLACE MY ATOMISER HEAD OR COIL IN MY TWISP CLEARO POD?expand_more
The Twisp Clearo Pod’s atomiser head is the same as that of the Twisp Clearo 3. To replace the atomiser head:
- Remove the pod from the battery
- Make sure the tank is empty. Now turn the tank upside down
- Lift the D-ring and unscrew the atomiser base
- Unscrew the Twisp Clearo atomiser head from the base and dispose responsibly
- It is recommended to prime a new atomiser head by dripping a few drops of flavour into the top of the new atomiser head, to help soak the wick before heading. 3-5 drops should suffice
- Replace the atomiser head and re-assemble
- Fill up your pod and wait a few minutes to allow for proper wicking before use
WHY AM I GETTING A BURNT TASTE WHEN USING MY TWISP CLEARO POD?expand_more
Consider refilling your pod before completely empty. There should always be some liquid covering the 4 wicking slots on the inside of the pod. If you taste a burnt flavour it is due to the atomiser head drawing insufficient flavour. the atomiser may have run dry. The atomiser should be replaced.
Atomiser heads do wear out over time. Replace the atomiser head when you taste a dry or burnt flavour. To change the atomiser head:
- Remove the pod from the battery Make sure the tank is empty or low and upside downLift the D-Ring and unscrew the atomiser base
- Unscrew the Twisp Clearo atomiser head from the base and dispose of responsibly
- Prime your new atomiser head by dripping 6-7 drops of liquid onto each feeding hole on the coil (white holes on the side of your coil) and allow it to seep completely inside the coil then move to the next feeding hole in a clockwise direction.
- Replace the atomiser head and re-assembleReplace the atomiser head and re-assembleFill up your pod and wait a few minutes to allow for proper wicking before use
Important to note:
It is recommended to refill your pod after inserting a new coil.Important to note:Remove the pod from the battery.
Do not use water to clean the atomiser heads/coils
- Remove the pod from the battery
- Make sure the tank is empty or low and upside down
- Lift the D-Ring and unscrew the atomiser base
- Unscrew the Twisp Clearo atomiser head from the base and dispose of responsibly
- Prime your new atomiser head by dripping 6-7 drops of liquid onto each feeding hole on the coil (white holes on the side of your coil) and allow it to seep completely inside the coil then move to the next feeding hole in a clockwise direction. Replace the atomiser head and re-assemble
- Fill up your pod and wait a few minutes to allow for proper wicking before use
Important to note: It is recommended to refill your pod after inserting a new coil
Important to note:- Remove the pod from the battery
- Do not use water to clean the atomiser heads/coils
HOW DO I REFILL MY TWISP CLEARO POD?expand_more
Consider refilling your pod before completely empty. There should always be some liquid covering the 4 wicking slots on the inside of the pod.
- Rotate the pod/device so that the silicone flap is facing upwards
- Gently lift the silicone tab from the dot side of the flap
- Fill the tank through the exposed fill port, do not overfill the pod, as an air lock can form
- Replace the seal, ensuring that the seal is fully flush within the filling recess
- If the pod was removed from the battery, please re-insert
Important to note:- Remove the pod from the battery
- Do not use water to clean the atomiser heads/coils
WHY IS MY TWISP CLEARO POD LEAKING?expand_more
Leaking occurs when air can enter the tank. This is usually due to a crack in the tank or a missing or damaged seal. If your tank leaks out of the vent, please check the following:
Important to note:
- Make sure the atomiser base seal is present and undamaged
- Check that there is an atomiser head in place, and correctly installed
- Make sure the pod tank and atomiser base are properly screwed together - finger tight is perfect
- Make sure the pod tank is in good condition and there are no cracks
- Check to make sure the silicone filling tab is closed correctly. Upon checking and correcting also clear any liquid that might have accumulated in the atomiser base.
Upon checking and correcting also clear any liquid that might have accumulated in the atomiser base. HOW DO I CLEAN MY TWISP CLEARO POD?expand_more
We recommend cleaning the pod tank and atomiser base on a regular basis (recommend roughly after 10 refills). Always clean and dry the pod tank if you are storing for a lengthy period. To clean:- Disassemble the pod tank into its component pieces
- Remove the atomiser head and set aside
- Rinse tank components thoroughly with warm water
- Clean out any excess liquid that may have collected in the atomiser base by using a soft tissue or cloth
- Wipe off any excess liquid from the base of the atomiser head
- Reassemble and fill as per filling instructions
Important to note:- Do not expose the battery to any cleaning liquids
- Do not use water to clean the atomiser heads/coils
WHAT DO THE DIFFERENT LED LIGHT INDICATORS MEAN ON MY TWISP CLEARO POD?expand_more
- Charge level indication takes place in the power button (main Indicator light) after every button press. The single LED light is used to indicate the level of the charge in 3 increments. A white indicates a 100-65% full battery. As the charge drops the light changes from white, to blue (65-30% full), and finally red (30-0%)
- Charging is indicated by the same main indicator colour LED light, once charging initialises the light will briefly cycle through its 3 colours. As the charge increases, so does the colour index
- Boost mode enabled: The boost indicator will light up white when the boost indicator button is pressed and activated. Pressing the same button will disable boost mode and revert the power output to normal, while turning off the indicator light
- Connection error (short circuit): In the unlikely event that your atomiser head or battery short circuits, the power will shut off, and the top and bottom LED lights will flash alternately. Please reseat the atomiser head, and or the pod, or contact Vuse Care
should the problem persist - Overheat protection: If the button is pressed for longer than 10 seconds, the power will shut off to prevent damage to the atomiser head, and the main indicator LED will cycle through the three colours for a few seconds. The device can continue to be used normally thereafter
- Overcharging protection: To protect the battery, the charging power is shut-off when the charge is completed
- Low voltage protection: When the battery voltage drops lower than required, the main indicator LED will flash 4 times in red and the device will lock. Charge the device and power it back on
